automatically in X axis for programmable hole-to-hole
block honing – hones a line of cylinders unattended.
Automatic Lower Crash Protection System
Many Engine Blocks have interference in the lower area of the bores and can damage honing stones and holders. Every
time the H85X starts honing a cylinder, the machine will check bores for interference avoiding potential damage to honing
stones and holders. Variances in lower bores are common. Rottler H85X Control senses lower bore interference prior to
rotation and stroking stroking motion starting at full power, eliminating any stone or holder damage.
Automatic Lower Crash Protection System – every time cycle start is activated, the machine will check that the stones will not interfere with lower bore before starting rotation and stroking preventing stone and stone holder damage.
Spindle Taper with Quick Change System – change hone heads in seconds without any wrenches
Automatic Honing Stone retract at End of Cycle – the machine will automatically retract the stones during last stroke so that the stones do not leave any scratches or marks in the bore.
Automatic Cross Hatch Angle System – the machine will automatically adjust parameters to programmed cross hatch angle and finish the bore to programmed angle.
Automatic Roughing and Finishing Load Sensing System – machine short strokes or dwells anywhere it senses a tight area.
Electronic Hand Wheel for lowering hone head into each bore
Automatic Stone Feed-out System – once hone head is positioned in the bore, the machine automatically expands stones and rotates slowly before starting hone cycle
Automatic Plateau Brush Finish Program – the machine automatically expands plateau brushes to programmed load and counts down number of plateau strokes, then withdraws the brushes and retracts to the clearance position.
Control and programming through 15″ (400mm) CNC Touch Screen Control
Precision Display in .0001″ (.002mm) resolution
Industrial PC with Windows Operating System
USB Flash Drive and port for file transfer
Remote training, service and support via internet connection to machine (required)
Operation in either American or Metric systems
Horizontal Movement (X Axis) – Left and Right Direction – 38″ (965mm) – movement is on linear slidways and is powered by servo motor
Horizontal Movement (Y Axis) – Front and Back Direction – 3″ (75mm) – movement is manually on linear slideways
Vertical Movement (Z Axis) – Up and Down – 19″ (483mm)
Stroking System – CNC SERVO Controlled High Pitch Ball Screw System
Infinitely Variable Stroke Speed Control – Variable from 0 to 1500IPM (38m/min)
Rapid Stroke System Acceleration – 250in/sec (6.35m/sec)
Spindle Rotation System – CNC SERVO Controlled High Torque Spindle Rotation System – 44 ft.lbs (60NM)
Infinitely Variable Spindle RPM Control – Variable from 0 to 400RPM
(2) Stone Trays for up to 6 stone holder sets with built-in Dial Bore Gage Holder
Hone Head Storage Rack for up to 5 Hone Heads
Coolant System – Large Capacity coolant tank 70 Gal (265 Liter) – tank is located under the machine on wheels and is removable for servicing from front or rear of machine
Magnetic system for primary filtering inside coolant tank. Magnets are removable for easy tank cleaning once tank is removed from under the machine
Lifetime Magnetic Canister Filter System includes tools for cleaning filter.
Replacable Cartridge Canister Filter System. Dual Gradient 50-5 Micron replacement filter cartridge keeps coolant and cabinet clean. Filter Cartridge 514-2-42C
Machine Cabinet finished in Baked Enamel Power Coated for easy cleaning and appearance
Operation, Programming and Spare Parts Manual – Digital
Paint Color Code: RAL9002 (Grey White)
Electrical requirements: 208/240V, 30A, 50/60Hz, 3Ph
Shipping weight 2300 lbs. (1,043 kg)
Shipping dimensions: 60 X 72 X 93″ H (1524 X 2210 X 2337mm)
Prices (US Funds) FOB – EXW, Kent, Washington, USA
Rottler Software is designed
with Simplicity in mind.
Conversational software allows
operators to quickly and easily
learn and create their own
programs. It takes only a few
minutes to create a new program
for a new block then it is saved
for future recall and use
H85AX Machine Specifications American Metric
Control CNC Touch Screen
Machine Weight 2300 lbs 1045 kg
Diameter Range 1.69″ – 7.38″ 43 – 186mm
Torque at Hone Head 585in.lbs 265NM
Stroker Motor Torque 88.5in.lbs 40NM
Stroke System Acceleration 200in/sec2 5m/sec2
Spindle Stroke Speed 0-1500ipm 0-38m/min
Spindle – Motor Torque 114in.lbs 53NM
Stroker Motor Power 3.3HP 2.47KW
Workpiece Capacity – Length 55″ 1400mm
Travel – Horizontal (X Axis) 38″ 965mm
Spindle – Rotation Speed 1 to 400 RPM
Spindle – Motor 3.7 HP 2.77 Kw
Coolant Capacity 70 Gallons 265 Liters
Maximum Length of Cylinder 17″ 432mm
Stroke Length 19″ 483mm
Dimensions – Shipping 60D x 49W x 88″ H 1.5D x 3.8W x 2235mm H
Electrical Requirements 208/240V, 30A, 50/60Hz, 3Ph
Paint Color Code RAL9002 (Grey White)
PRICE SUBJECT TO CHANGE WITHOUT NOTICE.
For more information about this product, please contact us by email or by phone at 514-594-3213
Pour plus d’informations sur ce produit, Contactez-nous par courriel ou par téléphone au 514-594-3213